Many people don’t know how to install LED strip lights. Installing led strip lights is a great way to add some extra light to your home or office. Not only are they stylish and modern, but they also provide a lot of functional benefits. In this blog post, we will show you how to install LED strip lights in just 5 easy steps!
Choose the right LED strip lights for your needs
Before you start to install LED strip lights, you first need to choose the right type of light strip for your needs. There are a few different types of LED strips available on the market, so it’s important to select the one that is best suited for your specific application.
If you are looking for general ambient lighting, then a standard white LED strip light would be the best option. If you need more specialized or targeted lighting, then there are also color LED strips and RGB LED strips available which can provide a wider range of colors and brightness levels.
Once you have chosen the right type of LED strip light, make sure to measure the area where you will be installing them to ensure that you order the correct size. Be sure to measure the length and width of both sides before placing your order, as well as any curves or corners that might be present in order for us to provide an accurate quote!
If you have any questions about how to install led strip lights and which type is best suited for your needs, please contact our sales department at [email protected]. We will be happy to help answer all of your questions and assist with choosing the perfect LED strip lights for your space.
Cut the strip to the desired length
Once you have your LED strip lights, the next step for how to install led strip lights is to cut them to the desired length. This can be easily done with a pair of scissors or a utility knife. Just make sure to keep in mind how much light you want and where it will be placed before making any cuts.
If you are unsure about how long the strip should be, we recommend leaving a little extra room on each side so that you can adjust it as needed. You can always trim off any excess later if needed.
Please note: The LED strip light cannot be cut in the middle! If you need shorter strips, please contact our sales department for assistance.
Peel off the adhesive backing and attach to a clean surface
Now that you have cut your LED strip light to the desired length, it’s time to peel off the adhesive backing and attach them where they will be used. Make sure that you are working on a clean surface with no dirt or debris present before removing any tape from the back of your strips.
The adhesive should stay in place for up to two weeks without needing additional support so there is no need to worry about them falling down after installation! It does help if these areas are cleaned beforehand though because some surfaces may not allow as strong an adhesion over time due to dust buildup between layers of paint etc… If this happens then we recommend using double sided tape (or similar) instead which can be found at most hardware stores.
Connect the wires and test before installing in the final location
The final step for how to install led strip lights is to connect the wires from your LED strip lights together. Take one end of each wire and twist them around each other until they are firmly attached; then plug in an adapter to see if it works! If everything looks good, you can move on to installing these strips where they will be needed most by attaching mounting brackets or clips onto walls, etc.
Test Before that how to install led strip lights: Make sure all connections have been made properly before testing out your new lights in their final locations just like with any electrical work! This way there won’t be any surprises when turning them on at nighttime. It’s also always better safe than sorry so don’t forget this important step during installation day because we know how many people forget this step to install led strip lights.
Make sure to keep LED strip lights out of direct sunlight or they may overheat
LEDs are sensitive to heat and should not be exposed directly in the sun. If they get too warm, the light output will decrease and eventually stop working altogether so make sure you keep them away from any direct sources like windowsills etc… A good rule of thumb is that if it feels hot enough outside where your LED strip lights are located then don’t turn them on until there has been some time for cooling down again (this could take several hours depending).
The best way around this problem though would be by installing an outdoor enclosure with adequate ventilation holes which would allow airflow without letting rainwater enter inside or damaging nearby plants due to excessive heat exposure! This means no more worrying about what might happen when leaving these strips ended while out of your home.
Sum Up Install LED Strip lights
Now that you know how to install LED strip lights in just 5 easy steps, there’s no reason not to add some extra light to your home or office today! Not only are they stylish and modern, but they also provide a lot of functional benefits. With such a wide variety of options available on the market, it’s easy to find the perfect LED strip lights for your specific needs.
